This is a one of a kind model of the Enterprise A in the world. The large 46 inch long model has it all! From the start, the starship was made with the entire detailing molded in. From the saucer to the wrap engines the detailing is everywhere. The patterns took two years to make. We wanted to make the patterns as accurate and beautiful as possible. Unlike others kits where the detailing is close, this model is right on!
All parts are hand laid up, using epoxy resin and cloth. This is done for strength and light weight. Then we go a step further. We install a brass and aluminum armature. This runs from the saucer to the secondary hull. This add strength and also helps to set the model on a tripod.
Brass rod is also laid into the struts that hold up the engines to provided strength and a place to run electric wiring to engines. All clear parts are cast in optical grade epoxy. This is the kit for the serious collector who demands only the best! The kit does not include wiring, lights, and paint. What it does include is all of the main hull parts "See Drawing", instructions, Aztec pattern for the main saucer, paint guide, decals and glue. Very important construction procedure: Use good quality paints and primers. See important note on this on the Reliant kit information below.
Because of the time consuming job of making each part, a very limited number of kits will be available. This will be on a first serve basis.
Each kit includes:
- 1-Secondary hull
- 1-Disk Housing
- 1-Front censor disk
- 1-Photon Torpedo tubes
- 1-Lower dome
- 1-Main Saucer Housing
- 1-Saucer Top
- 1-Bridge
- 1-Impulse Engine
- 4-Nacelle Front Side Grills
- 2-Magnatomic Crystal
- 2-Warp Engine Side Panels
- 2-Warp Engine Nacelle
- 2-Reaction Control Thrusters
- 2-Struts
- 1-Landing Bay Doors
- 1-Light Housing
- decals
- Instructions
Allow 2 to 4 weeks for delivery. Each model is made on order or call for time of delivery.
Catalog No.8000 Enterprise A Model Kit
Call or e-mail for price and availability on the Enterprise A Model Kit.
- PRICE: Call or E-mail for price of the Enterprise A Model Kit.
Catalog No.8010 Optional Stand
Optional stand with brass name plate.
- PRICE: $185.00- Optional Stand with brass name plate.
Postage in USA $65.00
Postage overseas call for price.
>>IMPORTANT<<The design characteristics and specific construction details of the hull shown in this material are the property of NORTHSTAR MODELS, who will make use of all legal remedies to protect its rights against anyone who copies or imitates them.
Copyright-NORTHSTAR MODELS
NORTHSTAR RELIANT KIT
Reliant Kit -No Longer Available
This is the perfect model to go along with your Northstar Enterprise A kit. It is in the same scale as the Enterprise, measuring around 36 inch long. Also, all of the detailing is molded in this kit. In fact, we found out that the Reliant had more detail than the Enterprise. Because of all this detail, we had to build rubber molds for all the parts. For this reason, we will only be able to make up to 15 kits.
The model is made up of Epoxy fiberglass for strength. The engine struts have all of the wiring molded in them. Bolts are molded in the struts to hold the struts to the main hull for assembly. The over head torpedo wing housing is also cast hollow, so you can install wiring up to the torpedo housing head. The model is simple to assemble and builds into a one of a kind beautiful show model.
Each Kit Includes:
-
2-Main Saucer halves
-
2-Engine struts
-
4-Engine halves
-
Bridge
-
Lower censor array
-
Rear impulse engine
-
Engine grill and lens
-
Torpedo wing, torpedo head with all of the necessary parts.
-
All necessary small parts, etc.
-
Decals
-
Instructions
VERY IMPORTANT CONSTRUCTION PROCEDURE:
On both the Enterprise and Reliant kits, it is very important that you use good quality primer and paints on the hulls. We use the Napa spray primer #7285 Lacquer primer. Before you prime, lightly sand the parts down with #600 wet and dry sandpaper, then use Napa Crose Fire Wax and Grease remover #15256. Use this before and after you sand. Do not use cheaper brands of primer and paints. Very important to use only high quality auto paints and primers.
Allow 2 to 4 weeks for delivery. Each model is made on order. Call or e-mail for availability.
CATALOG NO. 9000 RELIANT MODEL KIT
-
Call or e-mail for price and availability.
CATALOG NO. 9010 OPTIONAL STAND WITH BRASS NAME PLATE
-
PRICE: $185.00
Postage in USA $65.00
Postage overseas call for price.
Pictures of the Reliant Model.
